Asrock P4i45GV Rev 3.0 Driver
25 3 Chapter 1 Introduction Thank you for purchasing ASRock . IDE2 8 PGA VGA1 26 25 24 23 1 AUX1 AGP1 AUDIO1 P4i45GV REV. ASROCK P4I45GV R Manual Online: Motherboard Layout. (P4i45GL) 1 2 3 cm (in) 1 Mouse PS2 PS2_USB_PWR1 T: USB0 Top: B: USB1 RJ T. Keep updated software for your hardware device by the current Asrock drivers. Don't forget to get latest Asrock P4i45GV Rev Bios by Asrock update.
|Supported systems:||Windows XP, Windows Vista, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10, Windows 10 64 bit|
|Price:||Free* [*Free Regsitration Required]|
Asrock P4i45GV Rev 3.0 Driver
Chapter 1 and 2 of this manual contain introduction of the motherboard and step-bystep installation guide. Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to Asrock P4i45GV Rev 3.0 without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. Supports up to 2 floppy disk drives Audio: While CPU overheat is detected, the system will automatically shutdown.
- ASRock P4I45GV - motherboard - micro ATX - Socket - iGV Overview - CNET
- SOLVED: ASrock Prescott (P4i45GL) not recognizing AGP - Fixya
- AsRock P4i45GV bios update - TechSpot Forums
- Asrock P4i45GV Rev 3.0 Bios 2.9
- ASROCK P4I45GV R5.0 User Manual: Motherboard Layout
- ASRock P4I45GV - motherboard - micro ATX - Socket 478 - i845GV
Please check if the CPU fan on the motherboard functions properly before you resume the system. To improve heat dissipation, remember to spray thermal grease between the CPU Asrock P4i45GV Rev 3.0 the heatsink when you install the PC 6. It may not work properly under Microsoft? Please refer to Microsoft? Although this motherboard offers stepless control, it is not recommended to perform over-clocking.
Please refer to the table below for the details. CD1 Black 11 1. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Pre-installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings.
ASRock P4i45GV R5.0 Compatible Cases
Unplug the power cord from the wall socket before touching any component. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like.
Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. Hold components by the edges and do not touch the ICs. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Unlock the socket by lifting the lever up to a 90 angle. Position the CPU directly above the socket such that its marked corner matches the base of the socket lever. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct Asrock P4i45GV Rev 3.0.
The lever clicks on the side tab to indicate that it is locked. Thermal grease between the CPU and the heatsink is also needed to improve heat dissipation.
ASRock P4i45GV R User Manual
Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. For proper installation, please kindly refer to the instruction manuals of the CPU fan and heatsink vendors. Please make sure to disconnect power supply before adding or removing DIMMs or the system components. Unlock a DIMM slot by pressing the retaining clips outward. Before installing the expansion card, please make sure that the power supply is switched off or the Asrock P4i45GV Rev 3.0 cord is unplugged.
Please read the documentation of the expansion card and make necessary hardware settings for Asrock P4i45GV Rev 3.0 card before you start the installation. Remove the system unit cover if your motherboard is already installed in a chassis. Remove the bracket facing the slot that you intend to use.
Keep the screws for later use. Align the card connector with the slot and press firmly until the card is completely seated on the slot.
Fasten the card to the chassis with screws. Replace the system cover. For the detailed instruction, please refer to the document at the following path in the Support CD: